FreeOZ论坛

标题: 投了半年的简历，只有一次面试机会。不知道问题在哪里？ [打印本页]

作者: elyn86 时间: 12-6-2008 11:11
标题: 投了半年的简历，只有一次面试机会。不知道问题在哪里？
我老公是electronic engineer 做汽车音响的
在国内工作找他
但是到了这里半年了，简历不断的投，只有3月份有过一次面试的机会，做了technician的工作，一直到现在。

投简历从来就没有中断过，但是就是没有面试机会，要么完全没消息，要么就回信拒绝了。

不知道简历是不是有问题，希望大侠帮忙看看
如果大家有其他建议的，帮助我们找到问题的，不妨直说。先谢过了

这个是我老公的简历主要还是针对电子工程师的
Personal Comments:
☆ Over 5 years experience of electronics design;
☆ Advanced hardware and software knowledge of electronics product for automotive;
☆ Ability of CAD tools application for circuit design and PCB layout, such as Mentor Graphics DxDesign, Zuken Visula, CR-5000, Cadvance, and Protel;
☆ Quick learning and adaptation;
☆ Cooperation and teamwork spirit;
☆ Well organized;
☆ Communication skills in English, Mandarin and Japanese

Qualification / Education:
2005                               Professional Electronics Engineer
ENGINEERS AUSTRALIA
19xx –                                  Electric Information Engineer Bachelor Degree

Work Experience:
2008 S Australia
Work description:  Product test, PCB modification
Software debug for radio/monitor system, motor control system and fixed issues about the programs by C/C++

2005-2007 Y China

Electronics Engineer in Product Development Department

20xx-20xx  main designer for D, which was redesigned for cost down about 25%
Work description: 1 Achieve power supply and front panel circuit calculation, worst case analysis;
2 Analogue and digital circuit design including micro controller circuit, external electrical interface circuit, audio circuit including iPod interface design via CAD tool DxDesign;
3 Complete HSIS, HMI design and software test;
4 EBOM, DFMEA design, write alert / design change;
5 Implement tuner and audio performance tests; tuner performance improvements, Usable Sensitivity, Signal/Noise etc;
6 Implement radio vibration test, high temp and low temp test and tuner performance improvements at these conditions;
7 Support the production line in Portugal; solve problems of tests on line.

20xx-20xx M  front panel design
Work description: Front panel circuit design including key matrix and LED, LCD control circuit via CAD tool DxDesign, PCB layout via Visula.

20xx Joined the design team for T which won the V Innovation Prize in 2007, it’s a radio platform with CD, Mp3, USB, SD card and has been applied in a lot of car radio projects, such as M2, F, etc.
Work description: 1 Front panel circuit design including key matrix and LED, LCD control circuit via CAD tool DxDesign, PCB layout via Visula;
2 CD mechanism servo board circuit design including power supply circuit, MCU circuit, USB/SDCARD interface circuit via CAD tool DxDesign, burn the software into flash and test, etc;

2002-2005 P Co., Ltd China

Electronics Engineer in R&D Department Design Section 1

20xx –20xx  Finished design of 2DIN after market car stereo F series which have CD/MP3/MD or CD/MP3/CASSETE
Work description: 1 Front panel circuit design including key matrix and LED, LCD control circuit, motherboard PCB layout via CAD tool Cadvance;
2 Fixed Beat Noise problems in the RF tuner FM and AM
3 Audio (CD, MD) and Tuner (FM, AM) performance measurements
4 General performance measurements, such as max power, consumption current, etc;
5 EMC / EMI test, reliability tests, electrostatic destruction test; RF noise test
6 Support the production line in Shanghai

20xx – 20xx  Worked in P in Japan as electronic engineer and trainee, and finished design of 2DIN after market car stereo F which has CD,MD.
Work description: 1 Front panel circuit design including key matrix and LED, LCD control circuit, PCB layout via CAD tool CR-5000;
2 Implement audio and tuner performance test;
3 General performance measurements, such as max power, consumption current, etc;
4 Reliability test, fixed problem in electrostatic destruction test; RF noise test, etc
5 Implement EMC / EMI test.
6 Support the production line in Japan.

Professional Development
I have attended training courses in the following:
☆ DFMEA training course
☆ AM FM Radio
☆ CD MD DVD technologh
☆ 7 Habits of Highly Effective People
☆ 5S methodology

作者: dreamlife 时间: 12-6-2008 11:59
连电话都没有?

作者: elyn86 时间: 12-6-2008 12:10
只有中介电话来过，中介觉得蛮合适的，说把简历发给公司，估计几天后会有面试
但是过2天就电话说，公司拒绝了

作者: beysup 时间: 12-6-2008 12:10
澳洲的电子工业很落后，本国电子类产品全部进口，基本没有大型的研发，生产的公司，这个职业在澳洲很难发展。

作者: carl181818 时间: 12-6-2008 12:34
还是做电子产品维修吧，应该有机会。

作者: jason-zhu 时间: 12-6-2008 12:54
You are welcome to our free program:
http://www.freeoz.org/forum/thread-783661-1-1.html

作者: ritaclin 时间: 12-6-2008 13:34

原帖由 jason-zhu 于 12-6-2008 12:54 发表

 登录/注册后可看大图

You are welcome to our free program:
http://www.freeoz.org/forum/thread-783661-1-1.html

不是5月27号的活动吗？后面还有吗？

作者: dboy123 时间: 12-6-2008 20:16
该做控制系统吧，plc ,scada,dcs都可以。

欢迎光临 FreeOZ论坛 (https://www.freeoz.org/bbs/)